Anyone with an A35 that can do me a huge favor??(measurements)

upthemaiden · 03-10-10, 07:57 PM

I need a favor from anyone with an A35. I think I found some wheels for my moped(A3), I had the kid measure the wheels just to be sure that they would fit in my moped. They're not exactly the same width, but I think they'll work. Is there anyone out there with an A35 that would be able to measure the width of your fork and swingarm and tell me exactly how wide it is where the axle slides in? Not the diameter of the axle, but from the left fork leg to the right. I bought a pair of wheels before and they didn't fit, so I'd really like to be a bit more sure with these. If you could measure it in cm or mm that'd be awesome, if not I don't mind converting the measurements from inches.

Thanks!!

donp · 03-11-10, 07:07 AM

the only mag wheels that will fit and work on an a3 are those from a mid 80's silver bullet.

mattology · 03-11-10, 06:40 PM

I think puch wheels will be very close also

donp · 03-11-10, 09:08 PM

width wise maybe. but aren't they 17"? if so, they won't fit.

upthemaiden · 03-12-10, 08:20 AM

I don't know if they're ALL 17", but the ones on my wife's puch, as well as just about all the ones i've seen online were.

My wife's also has a much larger cog on the left side, not sure how big the carrier is, you might not even be able to fit one as small as the tomos on there because the brake is also on the left side because it has a bmx freewheel on the right side. There may be some puch wheels that are like our tomos, but her maxi would never cross over.

Either way, I've got one more set of wheels to try out on their way, so I'll see how they work. I'm just going to sell that last pair I bought. If these don't work I'll just find another pair and sell these again.

03-10-10, 07:57 PM	#1
upthemaiden TMO Member Trader Rating: 0 Join Date: Oct 2009 Age: 27 Posts: 319	Anyone with an A35 that can do me a huge favor??(measurements) I need a favor from anyone with an A35. I think I found some wheels for my moped(A3), I had the kid measure the wheels just to be sure that they would fit in my moped. They're not exactly the same width, but I think they'll work. Is there anyone out there with an A35 that would be able to measure the width of your fork and swingarm and tell me exactly how wide it is where the axle slides in? Not the diameter of the axle, but from the left fork leg to the right. I bought a pair of wheels before and they didn't fit, so I'd really like to be a bit more sure with these. If you could measure it in cm or mm that'd be awesome, if not I don't mind converting the measurements from inches. Thanks!!

03-11-10, 07:07 AM	#2
donp SuperModerator TMO Staff Trader Rating: 0 Join Date: Dec 2005 Location: Lyndhurst, Ohio Age: 43 Posts: 2,658	the only mag wheels that will fit and work on an a3 are those from a mid 80's silver bullet. __________________ MASTER REGIONAL RIDER who HATES the mra moderators http://budlight.whipnet.com/mp3/moped.mp3 Mow-Ped Mowers-Bicycles Service and Repairs 1695 Sunview dr Lyndhurst, Ohio 44124 i set up a myspace to host moped manuals. http://profile.myspace.com/index.cfm...id=228 297811

03-11-10, 06:40 PM	#3
mattology TMO Member Trader Rating: 0 Join Date: Aug 2009 Age: 27 Posts: 320	I think puch wheels will be very close also __________________ this website is a piece of junk, mopedarmy.com for life

03-11-10, 09:08 PM	#4
donp SuperModerator TMO Staff Trader Rating: 0 Join Date: Dec 2005 Location: Lyndhurst, Ohio Age: 43 Posts: 2,658	width wise maybe. but aren't they 17"? if so, they won't fit. __________________ MASTER REGIONAL RIDER who HATES the mra moderators http://budlight.whipnet.com/mp3/moped.mp3 Mow-Ped Mowers-Bicycles Service and Repairs 1695 Sunview dr Lyndhurst, Ohio 44124 i set up a myspace to host moped manuals. http://profile.myspace.com/index.cfm...id=228 297811

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-12-10, 08:20 AM	#5
upthemaiden TMO Member Trader Rating: 0 Join Date: Oct 2009 Age: 27 Posts: 319	I don't know if they're ALL 17", but the ones on my wife's puch, as well as just about all the ones i've seen online were. My wife's also has a much larger cog on the left side, not sure how big the carrier is, you might not even be able to fit one as small as the tomos on there because the brake is also on the left side because it has a bmx freewheel on the right side. There may be some puch wheels that are like our tomos, but her maxi would never cross over. Either way, I've got one more set of wheels to try out on their way, so I'll see how they work. I'm just going to sell that last pair I bought. If these don't work I'll just find another pair and sell these again.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)